I’m going to show you step by step how to build a gaming pc.
Table of Contents
When choosing components for build, the place I always like to start with is the processor. Now, this is going to dictate a lot of my other choices for picking different components for my build.
And really, when it comes down to the processor, there are a couple of major choices AMD and Intel. Now for this specific build, I’m going to be going with the ryzen 530 600 x. So for this build, I’m going to be using the Asus tough beat 450 m plus, not only is this a solid mid-range board, which is microwave.
Oh, this is microwave TX, the one I was looking for certain funny, the thing I like about this is it now is that a solid mid-range board that will fit in our case, which I’ll show you in a second.
But on top of that, it will support our rising processor, you have empty slots, basically a lot of the things that you would typically look for in a motherboard, this has it. And thanks to our wonderful sponsors that microcenter they have a combo deal. So you get like 20 bucks off on a buy this as well as the ryzen processor together.
AMD has actually done a good job recently of shipping pretty solid coolers in the box. And especially considering that this entire step is not particularly expensive, and actually makes a lot of sense for a semi-budget build. You can see it’s a fairly beefy thing. Now one thing I will say is on the bottom of any of these coolers Andy until one of the cases they will have a pre-applied thermal paste.
This is great. We don’t have to deal with any sort of tubes, whatever we can just drop This right on. However, don’t touch this when it comes to the processor, this is actually one of the more fragile components of the bill. So generally speaking, grab it by the sides, and do not under any circumstances, touch these tiny little gold pins on the bottom.
Because as an AMD processor, it has a lot of these pins. And if you’ve been any of these, it could very easily kill the CPU, all we do is lift up the little metal retention on you’ll see the entire socket moves back. So take a processor, there’s a tiny, tiny little gold arrow which has a corresponding little notch on the actual socket, all we do is line it up.
Again, do not force it just gently rested down and look at that, or CPUs installed, push the alarm down. Done. Simple, right? I know can be scary, right? I may or may not have spent a penny or two on a CPU in my lifetime. However, as long as you’re nice and gentle, do not push it into the slot, let it rest, if lined up, it will slide down and you’ll be just fine.
Read Full info about Gaming CPUs by click below here.
The next component I’d like to go for is the case. Now once you have your motherboard selected, which in our case is a microwave TX board means that you can pick what size case you want. So there are a couple of options with our specific build, we could go with a smaller Micro ATX chassis.
However, if this is your first time building a PC, I actually do generally recommend going with a little bit of a larger chassis. And because this is the H 510 means that we have a nice clean aesthetic, it’s all white actually does a good job of kind of hiding your cable management. So it’s a little cleaner, and you have a tempered glass panel, not bad for 70 bucks.
When it comes to building a gaming PC. Arguably the most important component is your graphics card. This is really what powers all of your gaming performance, it is a very crucial component. Now for this bill, because we are aiming for something mid-range. I think AMD is a brand new Radeon 5600 XT, which I very conveniently have right in front of me is going to be perfect at $208.
This should be plenty for literally any TVP game you can think of and even 1440 p if you really want to push it once you have your graphics card selected, and you make sure it will fit in your case, which shouldn’t be a problem unless you’re working with a very, very small case.
The next choice to pick is your power supply. So this is where something like this power spec 650-watt unit is going to be perfect. Now it depends on your specific sort of system on what kind of wattage and there’s actually a couple of features that you should pay attention to with the power supply. So one of them which is the actual size.
So there are a couple of different models. So there are s effects, which is again, for very small systems with a smaller power supply generally a little bit more expensive. Or you can go with something like a full-size 80 x supply, which is what 95% of people are probably going to want to do.
Now, this is actually a really solid option and only $60, you’re not only getting an 80 plus bronze rating, you always want to look for 80 plus on your power supply. If it’s anything lower than that you’re likely getting something very low quality.
And a nice little benefit with this is that it is a semi-modular supply, again to the little bit of that later. But essentially, it means that your cable management will be a lot cleaner because you only plug in the cables that you actually need as opposed to stuffing a giant pile of cables in some corner of your case when you’re not needing as much better.
So the PC opened up, our next step is to work with the power supply. Now, this is the semi-modular supply that I was talking about earlier. And there’s a good reason for that. So you see all these extra cables that come with Now depending on your build, you may actually want to use some or all of these, but odds are, you’re probably not going to want to plug all of them in.
And if we don’t have to say plugin five hard drives, we can easily just not use that it will make our cable runs a lot cleaner when you stole a power supply, you need to pay attention to where the fan is. So with a case like this, we could actually theoretically put the fan up or down. However, because if you look at the bottom of our case, we have a dust filter, we should have the fan facing down. So all of this might look complicated and confusing. However, it’s actually not that bad.
So let me walk you through a couple of the power connectors that we’re going to be using for this bill. If you look for the really big, fat guy, this is the 20 plus four pen, this goes into our motherboard, every single PC bill is going to need one of these rights
The next thing to look for is Ram. Now, this is an area that actually is fairly straightforward. So first of all, unless you’re building a very budget system, I would recommend at least going with 16 gigs of RAM. And beyond that, if you’re using an Intel processor, the speed is not incredibly important. DDR fours are pretty much all you need.
But if you are opting to go with an AMD ryzen system like we are, you do want to get something at least a little bit on the faster side of things not necessary, it will definitely work with lower speed memory, we can get something like this at Zinio at 3600 megahertz it will significantly speed up your performance. And importantly, it also has RGB. So there’s that the next thing you’ll need is your storage. Now, this is totally up to you.
If you want to use an old-school mechanical hard drive, by all means, go for it, you are going to get a lot of capacity. But they’re really slow. And at this point, I don’t really recommend it unless you want it as a secondary drive, you really should pick up some kind of SSD for your main boot drive, they have a couple of options here.
They’re the oldest school sejda style, which is a bigger kind of SSD, you actually have to mount inside the case, they’re generally going to be a little bit cheaper, but they are going to be slower. However, if you’re building a new PC today, pretty much every motherboard should support them two NVMe standards. And you’ll find that over here nowadays that a much smaller SSD, but importantly is going to be significantly faster, which is why we’re going to be going with the England premium SSD the 512 gig model, but generally, 6799 is well really fast and really good for 6799.
Extra things that makes PC perfect:
So that’s all you need to build the gaming PC itself however, you’re probably going to want a few extra things. So first of all, you’re going to need peripherals. So I’ve opted to go with hyper mic stuff this time around. So I have the pulse fire surge RGB mouse I have the alloy origins keyboard as well as the cloud singer headset. Generally speaking, a mouse and keyboard are definitely needed.
So it is time to actually how to build a gaming pc. So we are here in Microsoft, and we’re actually taking advantage of their workspace. Although realistically, all you need is a decent size table and a very rigorous set of tools. Philips screwdriver, literally.
So big reason why I chose to go with this case is that it is so wide open on the inside. So even though the motherboard won’t even fill the entire thing up, it’s really easy to run cables behind the back of the motherboard. And specifically, our power supply has a nice little basement to live inside.
Next up we have our CPU power. So this is a four-plus four pen, most of the time, you’re going to want to put these together and this also will go into the motherboard. But for some boards, you may only need the four-pin and that’s why it breaks apart, you can see it has a little clip on it. So it only goes in one way. If you’re building a game PC, the next connector is something you’re almost certainly going to need and that is the PCI power. Now, this is a six-plus two-pin.
So again, depending on your graphics card, you may need six and may need the full eight. And in many cases, you’re actually going to need multiple. installing our power supply is very straightforward. So their fan facing down, all we do is just slide it into place. If you look inside your power supply box, you should find four tiny little screws. Now, this is all we need to use to actually mount the power supply. To become a little bit closer here you can see there are four different holes. So I actually line up, line it up correctly.
There’s a hole, here, here, and here. And all you do is just screw it in. Now one tip, this is good for PC building, but it actually applies to a lot of things is to use a cross pattern on your screws, so don’t do it super tight. And then instead of just sort of going around in a circle, now we’ve got a top left, and we’re next going to screw the bottom right.
The reason why use a cross pattern when you’re installing power supplies or really any kind of PC component is it applies even pressure. So if you do like the left side first, the entire supply might actually be slightly misaligned. This is just good general advice. If you’re putting on like a car tire, you should use a cross pattern, you shouldn’t just go kind of like around in a circle.
Before we start building with the motherboard, let me give you a brief tour of what’s going on here. Because at first glance, well there’s a lot of stuff. So number one thing to pay attention to is this, this is the CPU socket, it is slightly different between AMD and Intel. But regardless, essentially you just drop your CPU in here and I’ll explain that in just a second. So these are our dense slots as the kids call them these days, the ram dims them. So it’s really straightforward, open up the little slots, and this is where we’ll be installing our memory.
To the right of this is our power connector. So this is that 20 plus four-pin the really big guy, that’s where that gets plugged in. And if you look on top of the CPU socket, this is the eight-pin power supply. So again, from the actual power supply, you’re plugging two things in here, the 20 plus four-pin and the eight-pin.
That’s it. This is our PCI slot. This is where you will install your graphics card. Now you actually have a couple of other slots. You can use these for things such as me if you’re doing a really crazy build multiple graphics cards, but usually, you’ll plug in things like you know a capture card or maybe like a Wi-Fi card or something in here, the nice thing to pay attention to is ours into the slot.
Now depending on the motherboard, you may have multiple these sometimes they’re actually on the back or underneath some kind of cover. This one’s thankfully right in the middle. And this is where you will install yours into NVMe SSD. One thing to pay attention to though, are these little screws right here.
You’ll see 2242 20 to 1620 to 80 and 20 to 110. Now based on what size your SSD is, it’s almost always a 20 to 80, you’ll want to plug in a screw or screw in a screw into one of these holes. And that screw will come with the motherboard. So that’s the only thing that kind of gets a little confusing because you definitely need that screw to keep it in otherwise it falls out and then you don’t have an SSD.
I think you are enjoying how to build a gaming pc, let’s move to the next point.
How to build a gaming pc, we need to toss on our cooler, which actually should be pretty straightforward. Because this is an AMD board and we’re using a bit of a larger cooler, we actually do need to remove these four screws on either side to remove these little plastic pieces. The reason I bring that up is if you actually look on the back of the motherboard, we have this little metal retention plate.
This actually needs to stay here, but we’re just gonna remove these guys. Don’t worry about that backplate too much, because it’s not going to go anywhere. If it’s Oh, holy. What kind of robot was having a bad day with this man?
Oh, yeah, one little tip. So there are actually a few ways this can go on, it doesn’t matter at all, except that you’ve got this little AMD logo, I’ve accidentally done it wrong where it’s upside down. So just keep in mind which way you want to do it.
But essentially, we have a window in our case. So this is the point where if you make bad decisions, people will judge you this cooler is very easy to install. So always do again, try to touch that thermal paste, it just lining up with the screw holes that we have right here should just rest right into place.
And with that, then we’ll just start screwing it in. Now another reason why you want to make sure that you’re applying even pressure is that we want to make sure that thermal paste on the actual CPU is making a nice solid firm attachment. This is starting to look like a thing, right, we have a big cooler and a CPU very important components.
So you’ll see that there’s a little cable that’s attached to the fan. So this is a four-pin header. Now there usually will be pretty close. So for example, ours is right here, a little CPU fan header, that’s really easy to install, you’ll see that there are a couple of notches here. So it means it only goes in one way, all you do is line it up and drop it right into place.
We’re ready to CPU and this is a complete guide on how to build a gaming pc and how you can fix all these components to the case.
So when it comes to installing RAM, there are a couple of things to keep in mind. So because this is DDR four, you’ll see that there’s a little notch in the middle, and the entire thing is actually slightly curved. So that means that you’re only going to be able to put it in one way, a line that does notch up with the corresponding notch on the motherboard. If you try to put it down, it’s not going in, you’re probably doing it backward. Now the next thing to keep in mind is which slots to use. So it’s actually a little bit complicated on Intel, it’s fairly straightforward on AMD, it depends.
So you’ll see here that we have four DIMM slots, which is the standard. So we have these two plaques. So it’s one in three. And then we have these two gray, which are tuned for. For Andy, you want to take advantage of these two. In fact, actually, if you look really closely, you’ll see these little asterisks behind beside D two and a two. These are the preferred memory slots dropping in the slot, and then three to one push, and there is our m install. Look at that we’re like halfway there. Don’t worry about the other look, we’re almost there, we’re almost there.
And the next one’s even easier. It’s our SSD. To install this SSD is very straightforward. So you can see it’s tiny, like the size of a stick of gum. Now to install. It’s very straightforward. But you do need to keep in mind we need a little bit of hardware from the motherboard box, which I don’t think you know. Yes, I did. Okay, so it’s really easy to lose this, you see this tiny little screw in the little adapter.
This is what we need to install our SSD. So for this, it does help if you have a little bit of a finer Philips head screw just because it’s really small. But essentially what we need to do is install the little What do you call it like it’s called like the nub, like the little screw guide. So because it’s a 20 to 80 SSD, the vast majority of SSD, you will be using an archway to at least install this finger tight. So there we go.
And now to install this, this D it’s literally going to take us like three seconds. So we line it up with Bill slot. So I usually put it in by with a little bit of an angle kind of working in to make sure it actually slides. So there we go.
The next step is to take our SSD screw out, and then just literally lean it down. Use the little screw to screw it into place to make sure it doesn’t pop out of the socket. You know look we installed our SSD in literally like 18 seconds. That’s it.
So now it is time to bring back our case. And now we have to just install the motherboard. Now, something that will very much vary between your cases is how you actually do this and specifically which standoffs you use. So I pulled this guy over what you’ll see There are a series of little brass standoffs. So these are painted black. Sometimes they’re actually gold. You can see there are standoffs on the top.
There are also some standoffs in the middle, and especially this is the case has a little post here. This is really nice because it’ll help us line it up there are also some standoffs on the bottom. The important thing here to know is that it’s actually very straightforward to install. The only thing we need to do before actually installing the motherboard is put in our I o shield. Now, this came with the motherboard.
And essentially, when you open it up here, it just slides into the back of the case. So you’ll see here that this is where your ports will surface and you want to make sure that this case is or this little shield is here to make sure that it looks nice because this actually is a little bit of an annoying thing because essentially, you have to kind of push it until it clicks. So I usually kind of work the corners until I see it not want to jump out of my hands quick for me. Like for me.
Hey, so now all we do is put our motherboard into our case. No, yeah, because I’m using this next case, I’ve got that little post in the middle. So as long as I get it kind of roughly lined up perfectly. Love it. And then if we can get it on the peg here, which we can, oh, well that motherboard in place. Now we just need to screw it in with like 300 screws that are helpfully labeled in our NZ XT little baggie.
And this will be very close to being done. Surprise, surprise, the way to do this best. So just start with one corner, get screwed in, and go the next corner and kind of work your way around to make sure that again, you’re applying even pressure and with that, we have a motherboard installed into our case. So if you flip it upside down or right side up, it hasn’t all come crashing out. And we’re actually getting pretty close. The next step is to install the graphics card which we so helpfully have right behind the case it’s almost like a plant out like that, look at that.
These are our PCI connectors. So this is what will attach the graphics card to the motherboard, which will go into this slot right here. And then if we look around on the backside of the card, you’ll see we have a single eight-pin power connector. So with the help of our little video lights, you can actually see what’s going on. The next thing we need to do is actually install that graphics card.
So you’ll see right here, our PCI slot, the only thing we really need to do is take a look at that. And you’ll see it corresponds to these little metal connectors here. So these PCI slot covers, we just need to remove based on where the motherboard and the graphics card say. So we do just remove this little cover on the back.
So not all cases actually use this, although it’s becoming a more popular thing. And wow, what jacked up robot cranks screw it hold balls. So remove this little piece. And the next step is to remove these top two screws, which should be pretty easy. No, it comes to installing graphics cards. This is a very difficult process, which is going to require a lot of concentrates. I’m just kidding. You just literally line it up to push it and it’s really easy. So just line up with a slot, click it, boom, done. Look at that.
Now I’ll use my giant screwdriver to put this little PCI cover back in place. And we’re next going to jump into cable management. Oh boy, the least favorite part of any PC bill. So one thing I am going to do is because this already has the cables sort of pre-run for the fans, I’m going to plug these in first, just because if I don’t do them first, I’m burying them and I won’t be able to touch them again.
That’s actually either really good engineering or really lucky. Now just like when we plugged in our CPU, these fans that are up top and on the back, are notched. So they’re only going to go in one way. These are three pennants posts for pen, but it doesn’t make a difference. There’s only one way to plug them in. So you see we have a little bit of extra slack. However, I’m just going to pull that around the back right now.
And we will forget that it exists or deal with it later. Whichever one I feel it. So I just plugged in the 20 plus four pen, they really big guy. All I have to do is just wrap it around here, go straight down. And that’s it. Once I’m done with everything, I’ll Velcro it and this is making my life easy. So you can see right here I plugged in the four-plus four-pin CPU power connector. Now it’s a little bit of a tight fit, especially in this specific case, however, I’ve run the cable up on the top.
Basically just keep in mind that as with most of these connectors, there’s a little notch on it, so it’s only going to go in one way. Next up we have our eight-pin PCI power connector. And because this only needs the one we have the extra lead, we’ll just deal with that later. We’ll just like cable, tie it up. But again, we’ll just line it up clicking into place when that’s it.
Okay, so we have a few different cables coming from the case itself. So we have a USB 3.0 lead. This is annoying because it will get stuck and you can easily break it so just be careful. We also have our audio so this is for our front panel audio. And we’re really excited about our front panel connectors. So these are typically separate.
So what you’ll see is you’ll have a bunch of little tiny individual connectors that will go to things such as the power button and the reset and the LEDs. Whoever is the XT was kind enough to provide one all in a single brick. So the first thing is we’re going to install our HD audio. So you’ll see this a little FP connector here and there’s one little pin knocked out on the top. There’s a corresponding pin missing here, which means all you do is light it up. And easily just plug it in like so.
Next, we have USB three, which is this guy right here. It’s the sort of larger connector, and it’s got the notch in the bottom, which corresponds here. Again, it’s pretty easy to install, but just if you ever have to install it, it’s a pain because it likes to just get stuck. And the next thing is the front panel connectors.
Again, these are the ones that usually suck. However, because I have my little notch sort of input, I can just do this and live a happy, happy life. So with that, we’ve built ourselves a gaming PC. So before we do any kind of proper cable management before start putting the size back on or anything, let’s first connect to a monitor and make sure it works.
Alright, so we had set up our computer, we plugged in our USB peripherals from hyper x as well as we have our headset here. We have our monitor connected, we’ve remembered to flip the switch on the back of the power supply, which I don’t see anything. Oh, yeah, we see some RGB action. That’s a good sign. Okay, we have power to our peripherals and we have a successful post. As soon as you see this, the first thing you should do is double-check everything’s correct.
So we have a ryzen 530 600 x 16 gigs of RAM, C’s keyboards, mice, that f1, and make sure everything is successfully showing up. This is you see it post that is a very, very good sign. There we go. We see our two eight-gig g skill dems, which will have to change the speed up and everything later. All of our fans are showing up 3600 x now from here, you want to do a couple of minor things. So we do want to go ahead and actually set up DCP. So we have our 3666 megahertz memory and beyond that pretty much good to go.
So we can start kill managing get this thing all sort of buttoned-up, install a copy of Windows, and you’ve successfully built yourself a gaming PC. I hope you enjoy how to build a gaming pc.
If you want to earn 6 figures money per month then Click below.